Cosina CSM

As I have mentioned elsewhere in this blog, Cosina have an undeservedly poor reputation. In fact, in addition to their own designs made under their own name, they make cameras for the big-name camera companies. The Zeiss Ikon rangefinder was made by Cosina as are many Carl Zeiss and Voigtlander lenses.

Cosina CSM

This camera is a Cosina design sold under their own name. It is fairly basic but with an electronically controlled shutter. I can tell that the shutter is electronically controlled because it  works without batteries but at the same slow speed regardless of the speed setting (a fully electronic shutter will not work at all without batteries). With batteries the shutter speeds are clearly variable.

The top plate is standard for a camera made in the late 1970s (introduced in 1978, I think). Far right is a small window for the frame counter. This is reset to zero when the camera back is opened. Next is the film advance lever. This is a metal plate covered with a plastic casing. It sits just proud of the back and is easy to use. It moves through about 210 degrees to advance the film one frame.It is not on a racket so just be moved in one motion.

In front of the advance lever is the shutter release button. this is chrome plated and threaded for a standard cable release. Below the shutter release is a lock switch. It has two positions - A and L. A is the working position and L is the lock position. I quite approve of shutter locks as over the years I have wasted many hundreds of frames of film by accidentally tripping the shutter. This lever is black.

Cosina CSM - top plate

Next along is the shutter speed dial. This runs from 4 seconds through 1 second to 1/1000 seconds. 1/60 is marked in red and I am sure will be the flash synchronisation speed. There are also positions marked in green - M and B. I have no idea what the M position is for and it is not mentioned in the manual (available from Butkus's website). B is for Bulb and is the standard of the shutter remaining open whilst the the shutter release is depressed.

Nested in the tangle of the film advance lever is a small chrome button. Pressing this disconnects the film advance mechanism to allow the film to be rewound.

The pentaprism hump has the accessory shoe on it. This has electrical contacts (so a hot shoe) synchronised for electronic flash (indicated by a red X). Cosina made an automatic exposure device which sat on this accessory shoe and connected to the shutter speed dial - this dial has a raised pin to allow the auto exposure accessory device to turn the speed dial, giving the camera aperture priority automatic exposure.

On the left of the pentaprism is the rewind crank. This is the usual fold-out type. The crank pulls up - to the first position to release the cassette in the camera and to the second position to unlock the hinged back. Between the pentaprism humpand the rewind crank is a white painted circle with e white line through it. The Lin represents the position of the film plane.

The front of the camera is fairly plain. most obvious is the lens mount. This is a 42 mm threaded mount - frequently known as the Pentax thread mount. This was the standard lens mount for several decades and so there are a vast number of lenses still available for this camera. The mount takes automatic aperture lenses (as well as older manual aperture lenses). There is a plunger at the base of the lens mount, just inside the thread. When the shutter release is pressed, this plunger moves forward and depresses a pin on the lens to close the aperture to the preset value. This ties in with the TTL light meter (TTL = Through The Lens). You focus and compose with the aperture wide open (and so with a bright image) and as the shutter release is half-way pressed, the aperture closes and the meter reads the light level. You then either adjust the aperture or shutter (or perhaps both) until the centre greed LED in the viewfinder is lit. Pressing the shutter release the rest of the way releases the shutter and takes the picture.

Cosina CSM - lens mount

Next to the lens mount at the bottom is a small chrome button. Pressing this allows the aperture to open again while the shutter release is partially depressed. You might think it easier to just take your finger off the shutter release button but the plunger does not return to its rest position if you do. If you want to re-compose or re-focus, you need this button.

On the right-hand side of the lens mount is a self-timer lever. This is turned through 90 degrees to set the mechanism.It is released by the shutter release in the usual way. On most cameras, These self-timers are clockwork and you can hear them ticking as the lever rotates back to its start position. Not here. This is an electronic device and the lever does not move back. Instead, a small red LED above the lever flashes once a second for ten seconds. After ten seconds, the shutter fires and the lever snaps back.

On the left of the lens mount are what at first glance appear to be two PC (Prontor Compur) sockets. In fact, only the lower one is - it is marked with a red X. This is for attaching an off-camera flash gun by a cable and is synchronised for electronic flash (by the late 1970s, bulb flashes were no longer usual and not catered for). The top connector is not quite the same as a PC connector and is designed for the automatic exposure device I mentioned above. It is marked with a green A.

On either side of the front of the camera are strap lugs - a small but very important feature to me.

The base of the camera has a battery compartment. It takes two LR44 (or SV44) batteries (which are still available). These power the light meter and the electronic shutter. There is also a standard tripod boss - 1/4 inch UNC thread. This is quite seriously offset from the centre of the camera which means the camera is likely to slope when on a tripod, particularly if a cheap tripod is used - this is a cheap camera so I don't supposed anyone would have used an expensive tripod.

Cosina CSM - base plate

Inside the back of the camera there is little to note. The shutter is a horizontally moving cloth shutter - absolutely standard at this time. The take-up spool has eight attachment positions of a fairly standard design so attaching the film leader would be easy enough.

Being Japanese, the camera relies on foam light seals to keep the film compartment light tight. This camera is 35-odd years old and the foam has long turned to sticky dust. The remains will need to be cleaned out and replaced with new foam before the camera can be used. This is a simple enough job, even for me.

Cosina CSM - inside the film chamber

Inside the viewfinder is uncluttered. There is a ground glass focussing screen with a horizontal split-image spot in the centre and around this is a circle of micro-prisms. The split-image centre works by placing it over a suitable vertical edge in the image. This edge will be split - part to the left and part to the right. When you focus the lens, these two parts move and line up with each other when the focus is correct.

In the absence of a suitable vertical edge, you use the micro-prism ring. When the image is unfocussed, this ring has a very granular appearance. As you get nearer to good focus, the granularity gets less and disappears at good focus.

At the top of the viewfinder are three LEDs. The central one is green and the other two are red arrows. While pressing the shutter release halfway, you adjust the aperture/shutter speed combination until the central green LED is lit steadily. The left hand red arrow lights up when you have too much exposure and the right hand arrow lights up when you have too little exposure. Very easy to use in practice.

The supplied lens - the kit lens if you will - is a Cosina made Cosinon lens - 50 mm focal length and maximum aperture of f/1.7 (and why not the industry standard of f/1.8?). The lens is multi-coated as you would expect from the late 1970s. This lens has an aluminium barrel and appears to be very well made.

Cosinon lens with six sided aperture

Cosinon lens - lens barrel

Cosina C1 35 mm film SLR

I got interested in Cosina cameras  while reading about the cameras they make for Big Name companies - companies like Canon, Nikon and Olympus. I started, many years ago, with the impression that Cosina only made cheap, low-spec cameras. That impression is now updated. My first Cosina was a CT1 (article coming) which is (still) sold by Nikon as their FM10 and was sold by Canon as their T60 and Olympus as their OM2000.

Cosina C1 - (C) John Margetts

lens: Cosina 35-70 mm zoom

focal length: 35-70 mm

apertures: f/3.5 to f/22 (nominally)

focus range: 0.5 metres to infinity

lens fitting: Pentax K-mount

shutter: Cosina metal focal plane

speeds: 1 second to 1/2000 seconds

flash: hot shoe, X synch

film size: 35 mm

This camera, the C1, is a much later camera.  The outside is plastic and so is (as far as I can tell) the chassis. This makes it feel to hold much like a modern DSLR. That is not a criticism of the cameras as a photographic device but as a collector of old cameras, the tactile component is important to me.

Once manufacturers turned to plastic mouldings, shape restrictions were removed. With this camera, while the internal chassis seems to still be rectangular (cuboid?) the outside has flowing curves. This is partially aesthetic and partially ergonomic. The camera is clearly designed to be held right-handed. There is a curved. raised portion on the front to give the middle two fingers a good grip and a second raised portion on the back to give a secure grip for the thumb. This leaves the index finger to comfortably sit  on the shutter release button. The curves continue around the pentaprism hump and in the junction between the body and the lens mount. my personal preference is for more classically designed cameras.

Cosina C1, top plate (C) John Margetts

The top plate has the standard layout - film advance lever, shutter release button and shutter speed selector on the right of the pentaprism hump and the rewind crank/door latch on the left. This camera has a standard hot-shoe accessory shoe (and no PC connector). The film advance lever acts as a shutter lock and light meter switch when the lever is flush with the body.

The front of the camera is unadorned apart from the Pentax K-mount lens mount and the name C1. This is the plain vanilla mount with no electrical contacts or autofocus screw. The rear of the camera is similarly unadorned - there is the viewfinder eyepiece and a window to allow the user to see part of the film cassette: ideal for those of us with virtually no memory.

Inside, the camera has no surprises. The shutter is a vertical travel metal shutter which is, I think, Cosina's own make. This offers speeds from 1 second to 1/2000 seconds and is synchronised for flash at 1/125 - marked in red on the speed selector dial. The speeds on the selector dial go anti-clockwise from 1 to 1/2000 seconds (the opposite way to the Cosina CT1).

Cosina shutter

The plastic back fits without light seals. the technique of moulding the plastic allows for sufficient light baffles without the use of foam. there are two exceptions: a small piece of foam by the hinge and a larger piece around the window to the film cassette. These are in good condition and the camera should still be usable without replacing them.

This camera comes with a TTL (Through The lens) light meter. It is powered by two LR44 batteries which are still available. On this camera, the meter does not work.

The lens that came with the camera is, I assume, the kit lens that Cosina provided with the camera when new. It is Cosina's own 35 - 70 mm zoom lens. It has an aperture range of f/3.5 to f/22 at 35 mm and f/4.8 to f/22+ at 70 mm. It is multi-coated and claims macro ability. This macro ability gives an image:subject ratio of 1:5 rather than the 1:1 ratio that is usually thought of as true macro. Focusing is from just under 0.5 metres (1.5 feet) and the focus scale is marked in both metres and feet.

The aperture scale is rather confusing. The aperture ring sets the size of the aperture (as you might expect) but the f-number is a ratio between focal length and aperture diameter. This means that the marked f/ stop depends on the zoom setting. For setting the aperture at 35 mm focal length there is a red dot for the aperture ring and at 70 mm focal length there is a green line (on the zoom scale, 35 mm is in red and 70 mm is in green). For zoom settings between 35 mm and 70 mm, neither mark will be quite right and you could be up to 1/2 stop out on your exposure, depending on whether you use the red dot or green line. in use, 1/2 stop + or - is neither here nor there. marked f/ stops are from f/3.5 to f/22 but this is clearly the case with  zoom setting of 35 mm. At 70 mm, the widest aperture is f/4.8 and the smallest is significantly less than f/22 - I would guess f/32.

The lens mount is Pentax's K mount. It is the plain vanilla mount as introduced in 1975. There are no electrical contacts or auto-focus screw so the lens is fully manual. Any K-mount lens will work with this camera so long as the lens has an aperture ring, and this lens will work on any K-mount camera - but only manually.

The lens is entirely plastic and does feel rather 'plasticky' but the adjustments are all very smooth and the lens looks to be well made.

Asahi Pentax MX

This is a very nice, if rather simple, compact film SLR from Asahi. It is intended as a professional camera and gives full manual control of exposures. In fact, all the camera uses the battery for is the light meter and it works fine with no battery.

Pentax MX (c) John Margetts

lens: n/a

focal length:   n/a

apertures: n/a

focus range: n/a

lens fitting: Pentax K mount

shutter: cloth focal plane

speeds: 1 to 1/1000

flash: hot shoe plus 2 PC sockets

film size: 35 mm

The layout of the camera is pretty standard for SLR cameras from between 1960-ish and 1985-ish. The top plate is metal (as far as I can tell. The three ME series cameras from Asahi had metallised plastic top plates). On the right is the film advance lever. This is metal with a black plastic tip. When not in use, it returns flush with the top plate. In use, it sits slightly proud. This allows easier access for your thumb when advancing the film and also allows easier access to the shutter speed dial. In front of the film advance is a window to the frame counter. This automatically resets to -2 (shown as S) when the camera back is opened. The counter then counts up from zero - two frames being used to remove the film fogged when loading the camera.

Next on the top plate, right at the front, is the shutter release button. This is chrome plated metal and is threaded for a standard cable release. Around this is a moveable collar. When turned anti-clockwise, it turns off the light meter and locks the shutter release. However, the shutter itself is not locked as it can still be fired using the self-timer. In the off/locked position, a small red 'L' is revealed to remind the photographer to unlock the camera.

Pentax MX (C) John Margetts

On the left of the shutter release button is a very small window to an indicator for the shutter status : white = not cocked/not ready

red = cocked/ready

Next along is the shutter speed/film speed selector dial. Shutter speed is set by simply turning the selector dial to position the required speed against the red mark - speeds are from 1 second to 1/1000 seconds plus B. To select the film speed, it is necessary to press a small button on the dial and turn.

Next is the pentaprism hump. This has a hot-shoe accessory shoe on top with then usual central electrical contact. It is marked with a red 'X' to signify that it is synchronised for electronic flash. For flash bulbs, there is other provision.

To the left of the pentaprism hump is the rewind crank. As had become usual by the time this camera was made, the rewind crank pulls up to both unlock the rear door and to free the film cassette for removal.

The front of the top plate is graced with the letters MX which are embossed in the metal and the name Pentax above the lens mount.  The Asahi logo and the name Asahi appear on the front of the pentaprism. Immediately above the name Pentax is a small window. This allows the set aperture to appear in the viewfinder above the image. Below the letters MX is the self-timer lever. This is activated by turning it anti-clockwise (which winds up the timer spring) and then pressing the small button revealed by moving the lever. This gives an eight to ten second delay and also (as mentioned above) will fire the shutter even when locked by the collar around the shutter release button.

On the other side of the lens mount are two PC connectors. One marked FP for flash bulbs and one marked X for electronic flash. These allow for off-camera flash as well as giving provision for using flash bulbs. These come with black plastic caps to protect the contacts when not in use.

The rear of camera is rather plain. There is the viewfinder eye-piece and the rear door. This door is opened by pulling up on the rewind crank. The door is made from black painted steel - on my camera, much of the paint has worn off and the steel has started to rust. In the centre of the door is a holder for the end of the film carton to act as a reminder as to which film is in use - an item all film cameras should have.

The base of the camera is intended to have a rapid wind attachment fitted and to accommodate this there are two holes to act as locating devices and a covered linkage to the film advance mechanism. As I do not have this rapid wind attachment, I can say no more about it. Also on the base plate is a covered battery compartment. This holds two button batteries - those fitted to my camera are marked 'GPA76'. Fortunately, Pentax did not rely on mercury batteries and these batteries are readily available.

The only other thing to mention is the lens mount. This is a K mount camera and any K mount lens will fit and work with the single exception of modern digital lenses with no aperture ring which, while fitting, will not be able to have their aperture adjusted. There are no electrical contacts on the MX version of the K mount as this is a fully mechanical camera but it does not mind lenses with contacts. I have three K mount lenses - a Tokina zoom, a Ricoh Riconar 55mm and a Sirius Automatic 28mm. All three work well with this camera.

Test pictures.

I am quite pleased with these - no light leaks, shutter working as it should - no pin-holes in the curtains and no hesitating curtains. In the second to last photo, there is severe vignetting. this is caused by me using a lens cap designed for a 50 mm lens with a 28 mm lens - the vignetting is actually the lens cap in view!

 This next one shows the joy of using the wrong lens hood - severe vignetting!

Voigtlander Vitoret 110

Voigtlander Vitoret 110, front view

I am not entirely sure why I bought this camera. The original thought came when I saw some Lomography 110 cartridges for sale in Snappy Snaps in Lincoln. When I saw this camera for sale on Ebay, I found myself bidding.  I was the only bidder and I got the camera for £1.00 plus postage.

It is not a complicated camera. It is a black box measuring 120 mm by 25 mm by 35 mm. The lens and viewfinder (both front and back) are covered by shutters when the camera is not in use. The camera is opened by moving the film advance slider. The shutter button is on top (it is coloured grey) and the film advance (also grey) is below it. If you hold the camera in a pinch grip with your right hand, your forefinger will land on the shutter button and your thumb on the film advance slider.  I don't think you could use this camera one handed as the camera needs to be steadied when winding on the film.

The lens is a Lanthar f5.6 lens - Lanthar lenses are triplets. There is no indication on the camera as to focal length but a search on Google tells me it is 24 mm - this is slightly wide for 16 mm film (normal would be about 26 mm) which is what we would expect for a point-and-shoot camera.

Vitoret 110, rear view

The viewfinder is a reverse Galilean finder (as was usual on consumer cameras by the 1970s)  and is quite large and bright with bright lines for framing - complete with close-up markings. The iris diaphragm is essentially square - so the bokeh will not be spectacular. The aperture can be altered but only by selecting weather icons. The pictorial instructions give f-numbers for these icons - sunny is f16, dull is between f11 and f8, light cloud is f5.6 all at speed 1/125 and dull cloud is f5.6 and speed 1/60.
--------------------------------------------------------------------------------------------------------------------------------
Blog copyright by John Margetts, 2014
---------------------------------------------------------------------------------------------------------------------------------

This camera uses the 110 film cartridges which just drop into the camera - no need to connect the film to the take-up spool. Opening the camera to insert the film cartridge is not obvious. You need to press a small grey button and slightly move the end of the camera (it only moves 2 mm or so) and then lift up the back.

Using the camera is very easy, there only being three controls: shutter button, advance slider and weather selector. Opening the lens/viewfinder shutters winds on the film. This means it is important not to wind on the film if you are going to put the camera away as when you next use the camera you will waste one frame. I found I kept forgetting to alter the weather selector, but as the light was only varying between sunny and dull I am expecting the latitude of the film to cope. Actually, this raises another point. the instructions mention using 80 ASA film (or 80 ISO for modern films) but the film I am using is 200 ISO which is more than twice as fast. it remains to be seen as to what exactly this means for my final prints.

Sample pictures:

These are reasonable - particularly if you consider that back in the day, these would have been printed as 5x7 prints at the largest.  Compared to a quality camera and quality film, they are a bit grainy but that is not really a proper comparison.  Biggest fault was my propensity to include a thumb in the right-hand edge of the pictures!

Holkham Hall, Norfolk

Filey, North Yorkshire

Humber bridge

Ropewalk Art Centre, Barton-on-Humber

Horncastle market

Horncastle market + close up of my thumb

Ihagee West - Exakta TL500

I do not intend to repeat the history of Ihagee here, suffice it to say that during the 1950s, 60s and 70s there were two Ihagee companies - the original Ihagee in Dresden that became absorbed into VEB Pentacon and a newer Ihagee West started by the original owner of the Dresden Ihagee (Johan Steenbergen) after he was unable to return to Dresden.  This camera is from Ihagee West rather than Ihagee Dresden. I say 'from' Ihagee West and not 'by' Ihagee West as they neither designed nor made this camera which bears their name.

Ihagee West Exakta TL500

In fact, this camera was designed and made by the Japanese company Petri. I am not saying that is a bad thing - Petri made some fine cameras and this camera is a fine camera - but it is not a German camera and does not carry any of the well-loved Exakta design concepts. The legend on the front of the camera says 'Exakta TL500' but in fact it is a re-badged Petri FT - the only clue to this is the stamp on the base saying 'Made in Japan'.

This camera is fairly heavy - it weighs 682 g with no lens - and measures 145 by 95 by 50 mm. This camera was made (or rather, marketed) in 1976 only (I have been unable to find much information about this camera or, indeed, Ihagee West other than neither maker nor camera were very successful). The layout is pretty much standard for the time.

Exakta TL500

Most controls are on the top plate. On the far left is the rewind crank. (the usual Exakta system of film cassette on the right and take-up spool on the left has not been maintained) and is the now usual small fold-out crank. This lifts to release the film cassette inside.

Next to this is the the film speed selector - the main scale is ASA and is printed in white, there is also a DIN scale printed in red. This selector moves in 1/3 stop click-stops - i.e. one degree DIN. The range is from 25 ASA to 1600 ASA (ASA being effectively the same as ISO). In the middle is the bump of the pentaprism with an accessory shoe on top. This has a central contact for flash and so is a hot shoe.

To the right of the pentaprism is the shutter speed selector. This goes from one second to 1/500 seconds in the usual sequence (the maximum speed of 1/500 gives the camera its name - its sister camera, the TL1000, had a top speed of 1/1000). Flash synch is marked with a red cross as 1/60. At the date of this camera, the makers will have assumed electronic flash.

On the right hand end of the top plate is the film advance lever. This is tipped in black plastic and moves through 180 degrees to wind on one frame.  Between the shutter speed selector and the film advance lever is a window for the frame counter. This resets to -2 (indicated by S) when the back is opened. This counter counts up from zero.

Exakta TL500 rear view

The front of the top plate, apart from the name, has nothing but the battery compartment. This holds a PX625A alkaline battery (still readily available). On the end of the top plate, on the left, is a PC connector for off-camera flash. Both the battery compartment and the PC socket are in unusual places. In fact, this is the first time I have seen a battery compartment anywhere but on the base plate. Unusual it might be, there is nothing wrong with it.  On the front of the camera there is nothing apart from the lens. There is no shutter delay lever on this camera. The lens mount has a standard M42 thread - Ihagee abandoned their Exakta bayonet mount right at the time that other camera makers were abandoning M42 threads. On the plus side, there were (and still are) a great many lenses available in M42 mount. Replacing the threaded mounting ring with an Exakta bayonet mounting ring would have been easy and cheap but it may well have cost more to do so while maintaining the correct lens-to-film distance. Regardless, Ihagee West went with Petri's M42 mount.

At the bottom of the lens mount is the TTL exposure meter switch. This is a stop-down system - pressing the switch stops the iris diaphragm down and switches on the electronics. To use, first you select your shutter speed, then press the meter switch and, while holding down the switch, turn the aperture ring until the meter needle in the viewfinder coincides with the white circle. It is possible to use this meter by setting the aperture and adjusting the shutter speed to match the needle-white ring but this is very awkward to do.  As the aperture stops-down to take the light reading, the viewfinder becomes very dark and it can be difficult to see the meter needle. 

At this point, I should offer a caveat to any new user of an Exakta TL500 (or TL1000). The exposure meter is automatically switched off by taking a picture. If you cannot get the meter to respond, wind-on the film. This is a good system as leaving the camera without winding on the film will prevent the battery from running down.

The base plate is uncluttered, having the rewind button and a 1/4 inch Whitworth (i.e. standard) tripod boss.  The catch for the back is on the left end and is pulled up to release the back.

Inside is as we would expect. On the left is the space for the film cassette, in the middle is the image window (24x36 mm) and on the right is the toothed sprocket that allows the film to be advanced a set number of sprocket holes. Right on the right is the take-up spool. This rotates in the opposite direction to the film advance lever. The lever moves counter-clockwise while the take-up spool rotates clockwise. This means that the film is stored emulsion side outwards..

Exakta TL500 - internal view

The edges of the back have black light-seal foam to prevent stray light getting in the join and fogging the film. This became normal in the 1960s but has the disadvantage that the foam eventually goes gooey and ceases to act as a light seal. I suspect that the designers of this camera would be surprised that their creation was still in use after forty years. I would imagine that cameras of the time had an expected life well within the useful life of the foam. Replacing light seal foam is both easy and cheap. I have a sheet of suitable self-adhesive foam bought on Ebay which only cost two or three pounds. The old foam can be removed with a cotton bud soaked in naptha (aka lighter fuel) and the new foam cut into suitable sized strips with scissors and then stuck in place.

I don't know what lens this camera came with when new but my TL500 came with an Auto Optomax. This lens is a 28mm lens so it is unlikely to be the original lens. Actually, this lens (which is in very good condition) makes a useful addition to my (small) collection of M42 lenses (this collection consists of a Helios-44 manual lens, Helios-44M auto lens, Vivitar 2x converter and this Optomax lens).

In use:

I had a spare half hour this morning and replaced the gooey light seals with new foam.  The camera should be good to go, so I have loaded it with Agfaphoto Vista + 200 ISO film (£1.00 per cassette from Poundland) and spent the morning taking photos of Lincoln. This camera came with no lens. I have been using my Soviet Helios-44M lens that came with my Asahi Spotmatic SP1000.  Tomorrow I am going to use my Optomax 28mm lens to finish off the roll of film.  Any M42 screw threaded lens will fit.

The first thing I have noticed using this camera is the weight. Over the last few weeks I have been using my Pentax ME Super and Olympus OM 10 - both of which are about as small as a film SLR can get and both are very light.

Not being made by Ihagee, all the controls are in the right place - i.e. both shutter release and film advance are on the right which makes using this camera fairly intuitive to use.

The camera is designed to use automatic lenses - which I am doing - but will still work with manual lenses (by 'automatic' I am referring to the diaphragm not the focusing).

To set the exposure, I need to choose a shutter speed, press the meter lever at the right side of teh lens mount base and while doing so rotate the aperture ring until the needle in the viewfinder is in the centre of the ring.  this sounds harder and more complicated than it is. The only problem I am having with this is finding the aperture ring by feel - this is not an issue with the camera, it is just that I am used to the aperture ring being on the outer edge of the lens barrel. 

The shutter/mirror action is quite good - not a lot of jar.

All in all, I am quite enjoying using this camera. there is one problem which is to do with the camera/lens combination. Focused on infinity, everything is fine. Focused on 0.6m. everything is fine. But if I focus on the hyperfocal distance (6m @ f11) the mirror will not return after the shot. Nor will the lens unscrew. To return the mirror I am having to re-focus to infinity, wind on the film and fire the shutter.  This has resulted in several wasted frames.  [EDIT: this happened over the first few frames of the first film. At exposure 16 it is no longer happening.]

When the film has been developed, I will post a selection of the test pictures.

16-11-2013

Here are a selection of pictures from my test film.  I am quite impressed.  All are exposed well so no problems with the exposure meter.  Exposure is even so the shutter blinds are moving smoothly.

Bridge over the Witham, Lincoln

High Street, Lincoln

Swans on the Witham, Lincoln

Housing estate road, Lincoln

Pentax ME Super

This is a very compact SLR from Pentax, Japan.  By the time of the K-mount cameras, the company had changed its name from Asahi to Pentax.  Originally, the Pentax name belonged to the East German Zeiss Ikon as a contraction of PENtaprism conTAX.  This camera is a development of the Spotmatic series.

lens: Sirius automatic
focal length: 28mm
apertures:  n/a
focus range:  0.2m to infinity
lens fitting:  K mount bayonet
shutter:  vertical metal focal plane
speeds: 4 seconds to 1/1000 seconds
flash:  hot shoe plus PC connector
film size:  35mm

The camera has an automatic exposure system that has aperture priority, the user setting the the required aperture and the camera selecting the shutter speed.  There is also a fully manual setting, the shutter speed being set by + and - buttons.

Pentax ME Super front view showing K-mount bayonet

The top plate is rather cluttered.  Starting on the left there is a combined rewind crank, film rewind crank, film speed setting (marked ASA) and exposure compensation.  The rewind crank is standard for the age of camera.  It folds out and is nearly too small for large hands.  Around this is a slightly knurled ring to set exposure compensation in one stop steps: +2 stops to -2 stops. Lifting the slightly knurled ring allows you to set the speed of the film for the light meter.  This runs from 12 ASA to 1600 ASA. That range is pretty much standard for automatic exposure cameras.  This is adjustable in one third stops which equates to a single degree DIN - there is no DIN scale available: even the Germans had gone over to ASA only by this time, at least on export models.

Pentax ME Super - top plate

In the centre of the top plate, on top of the pentaprism, is an accessory shoe with contacts for flash. This has the central contact that has become standard, and a smaller offset contact that is specific to Pentax flashguns.  This second contract allows elementary communication between camera and flashgun and lets the flashgun set the shutter speed to 1/125 seconds (the synchronisation speed) without the user doing anything.  With other flashguns it is necessary to set the shutter speed to 1/125 manually. There is a red cross embossed in the base of the accessory shoe to indicate that it is suitable for electronic flash.

In addition to the hot shoe connections there is also a PC (Prontor-Compur) socket.  This has two uses. First, it allows you to use a simple flashgun with no hot-shoe connection.  The second use is to allow the photographer to use off-camera flashguns.  This is of particular use in a studio where the photographer might have two or three flashguns all triggered from the camera.

Next to the accessory shoe on the right are a couple of buttons.  These are not marked - the markings by them refer to the mode dial.  These two buttons are used to set the shutter speed in manual mode - one button increases shutter speed, the other decreases it.

Beside the buttons is the mode dial.  This has five settings - Lock, Auto, Manual, 1/125x and B.  To turn this mode dial, you need to press down a very small white button on the dial pointer.  This is not impossible but I find it very hard to do.

The Lock position locks the shutter release button.  There are two reasons why using this is important. First, it prevents you taking accidental photographs while handling the camera.  The second reason is that partially pressing the shutter release activates the metering system and slight accidental pressure will run the batteries down.

Auto is the expected way of using this camera.  In this mode, the user sets the required aperture on the lens and the camera will decide on the shutter speed.  Cameras of this age do not have any electronic connection between the body and lens, communication being by two small levers.  In Auto mode, the camera selects the exact shutter speed needed for a good exposure, not just they nearest standard speed. The shutter speed selected is indicated by a LED on the left side of the viewfinder.  The speed indicated will be the nearest standard speed even if the actual speed is slightly more or less.  These indicator LEDs are in different colours.  Green means OK, yellow means a slow speed and a tripod is advised and red means no good.

Manual mode allows for manual operation of the camera (a bit of a give away in the name there!). Here, the user must select both aperture and shutter speed.  Shutter speeds are restricted to the standard speeds in one stop steps.

1/125x is for using non-Pentax flash guns.  Shutter speed is 1/125 and the user must calculate the aperture from the flashgun's guide number and the distance to the subject.  The reason electronic flashguns need a specific synch. speed with focal plane shutters is that the shutter exposes the film by a moving slit.  Shutter speed is determined by the width of the slit.  The flash from an electronic flash is very brief (1/10 000 seconds or so compared to 1/10 seconds for a flash bulb) and the width of the slit needs to be the width of the negative.  If you use electronic flash at a higher shutter speed, only a narrow portion of the negative will be exposed.

The last mode, B, is an extension on manual mode where the photographer must time the shutter himself - the automatic system only going as long as four seconds.

In the centre of the the mode dial is the shutter release button.  This is threaded for a standard cable release.  As already mentioned, partially pressing this button will activate the metering system.

To the far right of the top plate is the film advance lever.  This has a closed position with the lever parked over the top plate and a rest position where the lever sticks out at about thirty degrees.  The lever moves through about 130 degrees to advance the film one frame.  By the tip of this lever when in the parked position, there is a small window.  When you take a picture this turns to black.  When you wind on the film, this changes to red.  This is supposed to tell you if the camera is ready to use or no.  I find it easier to gently turn the film advance.  If it will not move, the camera is ready.  In front of the film advance is the frame counter.  Opening the camera resets this to -2 (indicated by a red dot).  On loading a film, you need to wind on the fogged start of the film which is two frames. Once you have done this, the counter will be at zero.

On the front right of the camera is a delayed action lever.  To use this, you turn it through 90 degrees to set it and then to activate it you nudge it upwards.  You then have ten seconds to get yourself in the frame.

On the bottom plate are a number of items.  In line with the lens is a tripod boss.  This is the standard 1/4 inch Whitworth.  Next to this is a battery cover.  this takes two button batteries of 400 size.  The meter electronics have a bridge circuit which means the exact voltage from the batteries is not important so when using alkaline batteries you can continue to use them safely until they are entirely flat.

At the opposite end of the base plate is what looks like another battery cover.  Under this is a mechanical connector for a motor-wind unit.  There are also three electrical contacts in a line which I assume are also for the motor-wind unit.

On the back is one of the most useful innovations in photography - a holder for the end-flap of the film carton.  Using this, you always have a reminder of the type of film in the camera.

Also on the back is a strange indicator.  This consists of a small window with black and red stripes in it. When the film moves - either advancing or rewinding - these stripes wobble.  The benefit is twofold - it tells you the film is inserted correctly and is advancing and it also tells you the film is rewinding.  When rewinding film, when these stripes stop wobbling you cans top rewinding.

Pentax ME Super back view

The lenses I am using with this camera are a Sirius 28mm macro lens and a Rokoh Riconar 55mm lens. Although Sirius lens is called a macro lens it is not really as the best reproduction ratio is 1:4 - macro is usually taken as being 1:1.

The Sirius lens focusses down to 0.2m (8 inches for my older readers) which is why Sirius call it a macro lens.  Looking on the Interweb, this lens does not have a good reputation but I shall make up my own mind when the test film is finished.  The claimed fault is that the lens is very soft.

Any softness apart, this lens is a delight to use.  Both the aperture ring and focusing ring are easy to find by feel - the aperture ring has wide ribs and the focussing ring has a coarse rubber knurling.

Focussing is through very nearly a complete circle giving very precise control over focussing.  This compares well with my modern Canon EOS lenses that only move through 80 to 90 degrees.

This lens is a prime lens and is multicoated.  The focussing scale is in both metres and feet which will benefit some although I am entirely metric.  The lens is made for a more modern K-mount standard than the camera.  The lens contains electronics (I can clearly see a resistor through the mount end) and has two electrical contacts in the bayonet.  It also has an aperture setting marked (A)P which I assume is to do with the electronics. The camera mount is plain machined, chrome-plated brass with no electrical contacts. However, this lens fits well and works well with this camera - the more modern K-mount is clearly backwards compatible with the original K-mount.

The Riconar lens is to the older standard - it has no visible electronics inside the lens and no contacts on the bayonet mount. This lens focuses down to 0.8 metres which is just under three feet.  Its aperture range is less than the Sirius lens - f2.2 to f16.  I am now using this lens with a roll of film and will post the results when I have finished the roll (the results below are for the Sirius lens only).

This camera is very small and light - it measures 130 x 45 x 85 mm - compared to most SLR cameras. It is certainly much smaller and lighter than the Spotmatic. The body of a focal plane shutter camera is always going to be longer than the body of a leaf shutter camera as the mechanism for the shutter plus the rolled shutter blinds must fit in there somewhere. Lighter will go with smaller.

Having made the camera smaller, Pentax have left enough room for my not-too-small hands to hold this camera securely. The final weight of the camera will depend on the lens attached but with no lens attached it weighs 445g. My two lenses are small prime lenses which reduces the total weight compared to using a zoom lens. On the other hand, these two lenses have metal barrels which will add weight compared to a modern polycarbonate lens. Any road, the lens/camera combination is one of the lightest of my collection.

I have created a small problem with this camera in that I have bought two lenses which focus in opposite directions. This is a camera I really like and I intend to use it as one of my go-to cameras. I am helped by the fact that I frequently change from SLR to rangefinder to viewfinder cameras and from German to Japanese so I have no instinctive expectations as to camera controls.

The only controls on the body that you use frame-to-frame is the on/off control and the shutter button. I find the on/off control hard to use as you need to press a very small white interlock while turning the knob. I am unable to do this with one hand and switching the camera on or off is a two handed affair.

The film advance lever, while the camera is not in use, sits very close to the body which is slightly awkward to use, but after the first shot it sits slightly proud which makes it much easier to use.

Walking around with this camera slung around your neck is much nicer than with most of my other SLRs - my OM10 being the exception. Both the ME Super and the OM10 are similar in size and weight. It is no hardship to use either of these two cameras on a long day out which is more than I can say for any of my German SLRs or my modern digital SLR.

Sad note: I picked up this camera today after cleaning it and the back swung open and my thumb went through the shutter - it is well passed repair.  But they are common enough so I don't expect it to take too long to find another one in good condition.

Sample pictures.  

These are taken on Agfa Vista + colour film, 200 ISO (actually made by Fuji) and the Sirius 28mm lens.  With the third picture, I have taken a detail from the centre to see how the lens performed as I have been told this Sirius lens is 'soft'.  My test reveals very little as the scan the lab did was only a medium resolution scan but this lens does not seem to be unduly soft to me.

Cannon Street, Lincoln

Wheat Harvest, Lincolnshire

Broadgate, Lincoln

Detail from above

Praktica MTL5B

This is my second Praktica (the other one being a Praktica TL3).  It is in good condition - including the battery compartment - and came with a number of extras.  These were a Vivitar 2x teleconverter (M42 thread so usable with my other M42 thread cameras), a Praktica flash, a Leningrad light meter and a cheap but quite good carry bag.

Praktica MTL 5B

lens:  Helios-44M

focal length:   58 mm

apertures:  2 - 16

focus range:  0.55m to infinity

lens fitting:  M42 thread

shutter:  metal focal plane

speeds:  1, 1/2, 1/4, 1/8, 1/16, 1/30, 1/60, 1/125, 1/250, 1/500, 1/1000

flash:  Hot shoe, no PC connector

film size: 35 mm

This is a fairly standard late 70s to mid-80s SLR camera. My first Praktica - I also have a TL3. It is squarish and heavy with minimal use of plastics.  It is 150mm by 95mm by 55mm, not counting the lens.  The controls are standard for the time and where you would expect to find them.  The film advance is on the top right of the camera and is a lever which moves about a quarter of a turn.  At this late date, advancing the film also cocks the shutter.  Next to the film advance is the combined shutter speed selector and film speed setting control.  Shutter speeds are noted above and are all any photographer could realistically want.  Film speed can be set from 12 DIN/12 ASA to 33 DIN/1600 ASA.  The setting can be changed in one DIN increments (one third of a stop).

The camera came with a Soviet Helios-44M lens which is not original.  The Helios-44 lenses have a very good reputation - they are good copies of the Carl Zeiss Biotar lens - and this one is in very good, clean condition.  It is an automatic version of the lens - I also have a manual Helios-44 lens which came with my Zenit E - with a switch  to change between manual diaphragm and automatic diaphragm.  The aperture can be changed in half stops which is an improvement on my other Helios-44 lens.

The shutter release is an angled button on the right face of the camera.  My finger falls fairly naturally on this and it is comfortable to use.  Right by this button is a plastic lever which actuates the TTL metering system.  In use, you put your finger on the shutter release and instead of pushing down, you push towards yourself.  The diaphragm closes and the needle in the right side of the viewfinder moves.  You then adjust either the shutter speed or aperture to get the needle lined up with the notch in the middle (this is basically a match-needle type of meter).  It is designed as a shutter priority system, the idea being that you set the shutter speed with the camera away from your eye and then move the camera to eye level and adjust the aperture ring with your left hand while pressing the meter lever with your right hand.  Used this way, it is fairly easy to use.

If, like me, you prefer aperture priority metering, you need to set the aperture first and then adjust the shutter speed while looking through the viewfinder.  It is just about possible to do this but it is very awkward to do.  I am finding myself moving the camera down to adjust the shutter speed which makes the whole operation slower and less fluid.  The meter is powered by a 1.33V button battery.  Originally, this would have been a mercury cell which is now not available.  I am using a same sized silver button of 1.5V which will cause a slight mis-reading of the meter but of less than a stop so this will not be a problem with negative film.  With reversal (slide) film this might be a problem.

Focusing this camera is a delight.  The focusing screen carries the usual plain ground glass screen with a micro-prism circle and a split-image centre.  However, the split-image part on this camera is diagonal. With a standard horizontal split-image centre, it is necessary to find a strong vertical to focus on.  With this camera either a strong vertical or a strong horizontal will work as will a strong diagonal.  When I was using this camera to photograph a bush earlier today, there were no verticals, horizontals or diagonals I could focus on. I used the micro-prism circle which also worked well.  For those who have never used a micro-prism focusing screen, what you do is focus until the micro-prisms disappear.  The further from focus you are, the more prominent the micro-prisms are.  Once you can not make out the micro-prisms (or until they are as indistinct as you can make them) the image is in focus.

Below the shutter release there is a self-timer (Vorlaufwerk in German) which works by turning the small lever through 180 degrees and then pressing the centre button to actuate the shutter instead on using the shutter release button.  This does work on my camera but not well.  It is very hesitant and stops for significant times but the mechanism is clockwork and has probably not been used for the thirty years since the camera was new.

The left side of the camera is bare apart from the rewind crank.  This is the normal small folding crank  that became usual during the 1960s.  It is released by pressing a button on the base of the camera.

The other external features are a frame counter beside the film advance lever which is reset by opening the back of the camera.  This counts up from one.  I prefer the Voigtlander system from the 1950s where the frame counter counted down to tell you how many frames are left but this did not become the industry standard.  There is also an accessory shoe which is a hot shoe in flash terms.  There is no PC connector (these had become passé by the time this camera was made) so flash must by on-camera flash or the photographer must buy a third-party flash attachment to allow studio flash.  The tripod boss is not on the base plate but moved forward onto the underneath of the lens mount.  This will give better balance when using longer lenses and is something I have not seen on more upmarket cameras although it makes a lot of sense.

The outside of the camera is 'silver' plastic top and bottom plate and a padded leatherette which is very nice to hold.  This is a big improvement on the standard leatherette on my Praktica TL3.

Inside is mostly standard film SLR layout.  The shutter is a metal vertical focal plane shutter.  Superficially, this is the same as on my Canon SLRs with several horizontal metal strips.  However, the fixing does not look as sophisticated as the Canon's shutter.  It does, however, work well and offers shutter speeds up to 1/1000 and flash synchronisation at 1/125.

This camera has automatic film loading.  You pull the film leader out to the green mark on the right and wind on.  One of two metal loops will then pull the film onto the sprockets and around the spool.  This works very well although the manual mentions that with particularly curly film it might be necessary to manually move the metal loop over the film.

Light seals are foam by the hinge of the back and black 'string' along the top and bottom of the recess the back fits into.  These pieces of string look rather amateurish but have the advantage that they will not deteriorate like foam always does.  On this camera the string light seals as as good as new while the foam light seal by the hinge is reduced to a sticky mess and needs to be replaced. (edit, 27-2-2017: I am advised by James Hays that the strings are not original items and have been added by an owner.)

Sample pictures.

These pictures are taken on Agfa Vista + colour film from Poundland (£1.00 per cassette!) and developed and scanned by Snappy Snaps in Lincoln.  I am quite pleased with these.  I have also tried out the Vivitar 2x teleconverter to see how it performs.  I quite pleased with the results - a teleconverter is never going to be as good as using a designed lens - and I think the teleconverter is usable for non-critical work.

carving on Lincoln's Stonebow - 50 mm lens

carving on Lincoln's Stonebow - 50 mm + 2x teleconverter

Piano busker, Lincoln

Lincolnshire Wolds

Thimbleby main street, Lincolnshire